Wired Networking
61 articles
- Clicking on Rogue AP Detection on the Controller of the EWS5912FP will not scan or detect wireless signals.
- Can EnGenius switches be set up via CLI?
- Does the EWS7928P have a “Save” Button on the Maintenance bar of the GUI?
- How can I access EGS7228P through the console port?
- How can I access EGS7228FP through the console port?
- How can I access EGS5212FP through the console port?
- How can I access EGS7252FP through the console port?
- How can I access EWS5912FP through the console port?
- Cannot enable Rogue AP detection on EWS5912FP
- There is no “Under Approval” button on EWS5912FP Controller GUI.
- Client Isolation is automatically enabled when L2 isolation is enabled on the EWS5912FP Wireless Controller software
- What do the Trunk1 to Trunk8 under PVID of my EWS5912FP switch refer to?
- I cannot set Captive Portal on 2.4GHz/5GHs SSID profile using Neutron Controller on EWS5912FP.
- Does EnGenius switch supports Discovery Protocol to allow IP phones to automatically connect to the voice VLAN (LLDP-MED)?
- The EWS5912FP switch was updated to firmware version 1.05.26-c1.6.24. When configuring the SSID profile for managed Neutron APs, Client Isolation automatically enables when L2 isolation is enabled.
- On the Controller of the EWS5912FP, there is no option to enable the Captive Portal feature for the main 2.4GHz/5GHz SSID profiles.
- Does the EGS7228P support the Cisco Discovery Protocol (CDP)?
- A computer is connected to port 5 of an EGS7228P switch. The untagged VLAN has a VLAN ID of 2 but the computer is not getting a valid IP from that VLAN.
- Is there a way to set up multiple VLAN profiles at once on the EGS7228P?
- What is the Power Budget of my EnGenius Switch?
- How many VLAN profiles can be specified on the EGS7228P?
- Why can't I ping between 2 computers connected on EGS2110P?
- Subnet Mask and CIDR: How many valid hosts can be used on a specific subnet (Classless Addressing)?
- Uploading Firmware on an EnGenius Switch
- How can we identify if the EGS2110P is a V1 or a V2. What is the difference between V1 and V2? Are there any features on the V2 that is not on the V1?
- Which SFP modules are compatible with EnGenius switches?
- IPv4 Standard Reserved Addresses
- Why does EGS5110P display "0:timeout" when you change the IP?
- Should I use fiber or copper for my network ?
- Compatible SFP transceiver specifications (Connector type, Wavelength, Fiber type).
- How to Fix: Neutron APs status show as “offline” on the Controller.
- Why Subnetting is Important
- Is there an option to back up the configuration file on the EGS2108P?
- What type of cable should be used to connect a computer to an EGS/EWS switch’s serial port?
- Is there a length limit to PoE cable runs?
- What are the options available on the Neutron Captive Portal?
- SNMP support for the EGS2108P, EGS2110P, and EGS5110P
- What Serial Software can we use for EGS/EWS Switches?
- What trunking Protocol is supported on EnGenius Switches?
- How to update Neutron APs managed by a Neutron switch via OCU
- How can we identify if the EGS2110P is a V1 or a V2?
- What should I do if port 1234 is Closed after doing connectivity test on EZ Master?
- What are the settings to be used on the Serial Connection Software (e.g Putty/Hyper Terminal) for Switches?
- How can I set up vlan with VID2 as untagged not VID1 on EnGenius Switches?
- Can I connect non-PoE devices to the PoE switch's PoE ports?
- What ports should be opened for ezMaster to work?
- What does "Port Trunking" mean for EnGenius Switches
- How to Fix: Error 800 Windows 7 (L2TP over IP Sec Client Unable to Connect)
- I can ping my (3) EAP350v2 access points but the EnGenius Zone Controller cannot find them.
- Best Practices for EnGenius Managed Network Switches
- White Papers: Routers and Network Controllers (3rd party)
- White Paper: Using VLANs with EnGenius APs and Switches
- My EGS2108P locks up when DHCP lease time is up on the connected DHCP server.
- How to open Port on an EnGenius Router
- Naming Convention: PoE/PoE+ Switches
- Naming Convention: Non-PoE Switches
- Installing and setting up VMware Player for eZMaster
- Installing and setting up ezMaster on Virtual Machine
- I cannot save AP settings changes on the Controller after updating the EWS2910P firmware to v1.05.42_c1.8.55.
- ezMaster – Captive Portal Configuration Guide
- How to change and add user login on EnGenius EWS Switch?